Hydrocarbon Processing Copying and distributing are prohibited without permission of the publisher
Email a friend
  • Please enter a maximum of 5 recipients. Use ; to separate more than one email address.

Slurry-phase hydrocracking—possible solution to refining margins

02.01.2011  |  Motaghi, M.,  KBR, Houston, TexasSubramanian, A.,  KBR, Houston, TexasUlrich, B.,  KBR Technology, Houston, Texas

Opportunity crudes require more hydrogen addition to upgrade orphan product streams into higher-value ‘clean’ products

Keywords: [diesel] [fuel oil] [heavy oil] [hydrocracking] [coke] [coker] [catalyst] [gas oil]

Refinery margins are complex topic; margins are subject to substantial uncertainties and are impacted by global fluctuations in regional feed and product pricing structures. A conscientious analysis of historical data will indicate that for every one good year, on average, refiners are subject to seven years of depressed margins. New globalization trends, which include a changing transport-fuel supply/demand balance, geographic shift in consumption, soaring crude-oil prices, depressed natural-gas prices and impending regulations, all pose interesting challenges to the very survival of many small- and medium-sized refineries.

Definitions of profitability.

A simple analysis of refinery economics will reveal that margins are largely impacted by three basic factors; crude cost, type of products produced and disposition of low-value, stranded streams. While the first two factors are simple to understand, the relationship between the refiner’s ability to handle these orphaned streams and margins is more complex.

Crude price.

The cost of crude is the single most important factor in setting refinery margins. This is the primary reason for the recent surge in refinery upgrades targeted at processing “opportunity crudes.” While the definition of opportunity crudes is nimble and can vary from refinery to refinery, for the purpose of this article, it makes sense to simply define these crudes as the cheapest possible crude basket available to any given refinery on any given day. This basket may consist of heavy or extra heavy crudes, bitumen-derived crudes, high-acid/high-metals naphthenic crudes or high metals-containing, paraffinic, heavy inland crudes.

Most refiners are limited in their ability to handle this wide range of opportunity crudes; more often than not, they are constrained by the residues derived from these crudes. In recent years, the surge in interest over resid upgraders was catalyzed by the growing light-heavy differentials. This, in turn, forced refiners to evaluate their bottoms processing technologies, as margins dictated a higher percentage of heavy oils in their crude diet. Although the large light-heavy differentials have since diminished, this phenomenon is likely to be temporary. The renewed interest in monetizing heavy-oil reserves and the influx of substantial heavy crude volumes to the marketplace suggests that in the long run, refinery margins are likely to return, in large part influenced by the restoration of the light-heavy differentials. Central to this theory is that light-oil fields are on the decline and almost all new crudes entering the market place are substantially heavier than the current crude basket. This is evident by the decreasing API as shown in Fig. 1, of the composite worldwide crude blend and increasing volumes of extra-heavy crudes such as Canadian and Latin American bitumens.

 Fig. 1. Crude API trends, 1990–2025.

As the world’s supply of crude oil becomes heavier and contains higher sulfur levels, the challenge to the refiners will be compounded by the need to meet the growing demand for light, high-quality, ultra-low-sulfur transportation fuels. This leads to the next major determining factor that sets refinery margins, i.e., quality of products.

Product quality.

Global trends show a growing diesel demand and stable-to-declining gasoline demand (Fig 2). As the world emerges from the global recession and as the growth margin in 40% of the world’s population continues at a rapid pace, this trend can only be expected to amplify. With the majority of existing refinery configurations slanted towards gasoline production, the price differential between diesel and gasoline will widen over the long haul, validating the market tilt towards dieselization. In addition, regulatory demands will only accelerate the shift towards lower density, higher-cetane index, ultra-low-sulfur diesel production, as the regional outlets for lower quality transport fuels diminish.

  Fig. 2. Demand for gasoline and diesel, 

This combination of lower cost “opportunity crudes” and the need to produce high-quality distillate-selective products is an important consideration for refiners, when making long-term, high-dollar investment decisions.


The least understood variable in determining refinery margins is the disposition of stranded streams. Refineries are littered with low-value streams that are blended off, often downgrading higher-value products for the sole purpose of finding positive outlets for less saleable streams. While the ability to upgrade these streams is a major factor that sets refinery complexity, the solutions for these streams often rests in understanding its potential applications and value within and outside the refining industry.

The single largest stranded stream for most refineries is the vacuum residue (VR). The bulk of the operating refineries around the world have little or no residuum processing capability and produce large volumes of high-sulfur fuel oil and bunker fuel. A small volume is used to produce road asphalt. The future of VR is, therefore, intrinsically tied to the future of these three outlets.

The large growth market for residues may appear to be the bunker fuel market predominantly influenced by globalization trends and consequential incremental trade and shipping traffic. However, the use of VR as the major blending component in bunker fuel will come under serious scrutiny as new maritime regulations come in to effect starting in 2015 (Fig. 3). This will significantly inhibit VR demands, and the eventual solution may come from either the shipping or the refining industry.

  Fig. 3. Expected timeline for IMO regulation

While one of the solutions under debate involves using onboard flue gas scrubbers, this issue is more complex. There are several reasons to underscore the reluctance of the shipping industry to take on the burden of these operating facilities. Regulatory trends are almost always unidirectional, and the shipping industry can only expect the sulfur oxide (SOx) regulations to extend to nitrogen oxide (NOx), particulates, volatiles and other controls, not to mention the added capital investment, operating cost, monitoring and reporting requirements. Conversely, the refining industry is unlikely to invest in expensive VR hydroprocessing with the sole purpose of producing specification bunker fuels.

Regulation directs actions.

The global trends show a sharp decline in high-sulfur fuel oil demand (Fig. 4), driven mainly by environmental regulations. While the sharp decline in fuel oil prices seen through the mid part of this decade has been temporarily arrested by the installation of many cokers, a reversal can be expected as regulatory pressures extend to the rest of the world. As is evident from the crack margins, producing large volumes of fuel oil will result in negative refinery economics and cannot be sustained.

  Fig. 4. Declining oil demand trend, 1990–

Road asphalt is a relatively small market (Fig. 5), and environmental pressures are also likely to force refiners to produce specification-grade bitumens without resorting to air blowing. While this may lead to investment in alternate technologies such as solvent de-asphalting, the overall impact on the volume of stranded VR or its pricing, will be minimal.

 Fig. 5. Demand for asphalt for road and
 roofing applications, 1990–2025.

All of these factors lead to one obvious conclusion. Going forward, high refining margins will depend upon the ability to capitalize on opportunity crudes, while consistently producing high-quality distillate-selective products from refinery residues. Selecting the appropriate residue upgrading technology, therefore, is a critical part of this puzzle that will define the future of refining and refinery margins.

Selecting residue upgrading technologies.

To better understand the technology options, one must recognize that VR, in essence, is defined by what is not VR. The quality and quantity of VR is a function of crude selection and the lowest boiling impurity contained within the resid fraction that shows up as the limiting factor in the vacuum gasoil (VGO) fraction that is fed to a catalytic hydrotreater, hydrocracker or fluid catalytic cracking (FCC) process. The choice of resid conversion technology must be set by project economics, preferred reaction chemistry and mechanism of conversion aimed at reliably achieving the overall processing objectives.

We present seven questions that one would expect refiners to ponder as they investigate the appropriateness of available technology options. The direct relevance of these questions is premised on projected market trends and is intended to address the desire to achieve and sustain high refinery margins:
1. Has the technology been demonstrated in one or more large scale units?
2. Can the technology handle residues irrespective of the feed quality?
3. Can the technology achieve near complete conversion on a once-through basis?
4. Can the technology produce finished diesel-selective products?
5. Does the technology database demonstrate the ability to handle a whole range of crudes?
6. Can the technology do all of this with high reliability?
7. Can the technology achieve all of this at an attractive net present value (NPV)?

Aided by low crude oil prices and high natural gas prices, the delayed coker has, thus far, been the technology of choice for resid upgrading. When tested against the “seven questions” above, and weighed against the prevalent market conditions of the past, the conclusions are obvious.

However, going forward, with projected high crude oil prices, low natural gas prices and diminishing outlets for low-grade petroleum coke, the need for hydrogen addition is now here. In the rest of this article, we will examine the landscape of the available resid upgrading hydrogen addition technologies against this backdrop. As shown in Fig. 6, the technology choice for resid hydroprocessing is inherently determined by the metals and Conradson Carbon Residue (CCR) content in the residuum.

 Fig. 6.  Resid upgrading technology options
 as directed by CCR %.

Fixed-bed resid hydrocrackers.

Fixed-bed technologies have been used to hydrotreat residues containing low concentrations of metals and CCR. In most cases, the operation of these units is severely inhibited by the rapid deactivation of the catalyst system. The resultant combination of high operating pressure, low conversion, poor quality products and low catalyst cycle length make the process capital intensive with limited overall benefits.

To improve the economics of fixed-bed resid hydrocrackers, the unit must be protected from feed impurities. A feed cleanup unit such as a solvent deasphalter (SDA) may be installed upstream of the hydrocracker to reject the heaviest CCR and metals containing fraction as a pitch stream.

The SDA works on the principles of solubility driven separation and is capable of lifting light deasphalted oil (DAO) from resid feeds. For most crudes, especially the lower value opportunity crudes, the overall lift will be low, limited by the CCR and metal specifications set by the DAO hydrotreating catalyst.

As a result of the low DAO yield, the reject asphaltenic stream will be large and can range from 50 wt%–80 wt% of the VR. For refiners who lack an economic outlet for this pitch stream, the value derived from the incremental distillate production through hydroconversion of the DAO is negated by transportation and handling costs associated with moving the pitch from the facility. Thus, DAO derived from the vast majority of solvent deasphalters operating in fuel services is directed to an FCC unit.

Fixed-bed resid hydroconversion processes will achieve minimal overall resid conversion, will produce a large volume of fuel oil, and are inherently limited by changing feed qualities. This incompatibility is evidenced by high operating pressures, large capital investments, low catalyst cycle length and a maintenance-intensive operating history. The quality of the products will not meet Euro V specifications, and the overall investment will not be commensurate with the derived benefits. When tested against the “seven questions to ponder,” it is obvious that fixed-bed resid hydrocracking technology based schemes would need to be critically examined by the refiner on almost every issue.

Ebullated-bed hydrocrackers.

Another option that has been considered and practiced by refiners for resid conversion is the ebullated bed technology. In this case, the same deactivation phenomenon seen in fixed-bed technologies is inherent with the one exception: the issue of low catalyst cycle length may be resolved through continuous addition and removal of catalysts.

Every resid handling process is subject to asphaltene precipitation as the saturates and aromatics contained in the feed that hold the asphaltenes in solution are removed or converted. This phenomenon is essentially driven by asphaltene-solubility chemistry, and the achievable conversion is a function of the saturates, aromatics, resins and asphaltene content in the residue, which in effect defines crude compatibility. In most cases, these units operate at a nominal 55% to 75% conversion, and in an era of “opportunity crudes”, this inherent limitation must be recognized.

While refinery economics dictate the need to operate at or near the asphaltene-precipitation boundary limits, the operation of these units can be fairly complex as the refiner balances the need to operate at maximum conversion while minimizing reliability issues associated with asphaltene-induced fouling.

With this narrow operating window, any changes in feed quality can contribute to higher maintenance costs and low onstream factors. To achieve a relatively small overall improvement in resid conversion, and to improve reliability, operators often limit once-through conversion, recycle polynuclear aromatics (PNAs) and add other external aromatic-rich streams to help solubilize the asphaltenes, which, in turn makes the process more capital intensive and will result in higher operating costs. Although these processes are catalytic and use metal-containing catalysts, the conversion chemistry is a blend of catalytic cracking and deactivation-induced thermal cracking. Along with the addition of aromatic external feeds, the chemistry will result in lower naphtha, diesel and gasoil qualities requiring the streams to be re-hydroprocessed to meet Euro V product quality specifications.

This need to add two catalytic steps makes the process capital intensive, thus challenging the economics of this option. With declining fuel-oil prices, and tightening fuel-oil quality regulations, the large volume of unconverted fuel oil will leave the refiner with much of the same issues to deal with in the post investment scenario, although in a smaller scale. When tested against the “seven questions to ponder,” the choice of crudes, achievable conversion, product qualities, reliability and investment threshold gain significance.

Slurry-phase hydrocrackers.

With high crude price and low natural gas prices on the horizon, slurry-phase hydrocracking (Fig. 7) is emerging as the preferred approach for upgrading residue streams via hydrogen addition. The principles of slurry-phase hydrocracking essentially overcome the limitations of fixed-bed and ebullated-bed technologies and provide for substantially higher conversion of the residuum.

 Fig. 7. Typical resid hydrocracker flowsheet.

The primary conversion of residues can be achieved through either catalytic or noncatalytic routes. Investigations for using catalysts or noncatalytic additive systems for primary conversion of the residues can be traced back to the early 1900s and span the entire century, with several hundred patents that have been awarded in support of these activities. Over the past few years, substantial effort has been expended by technology providers exploring nanocatalysts to enable the primary conversion of residues at marginally lower operating pressures. While catalyst-based systems are technically viable, the use of a relatively expensive catalyst system, catalyst deactivation, low quality of derived products and the need for catalyst recovery, all contribute to the economic considerations which in the authors’ view, is likely to make this option less attractive.

Key performance criteria.

We will focus on the noncatalytic slurry-phase hydrocracking in the context of hydrogen addition and examine the appropriateness of the technology to the current market conditions.

Has the technology been demonstrated in one or more large scale units? The origin of slurry-phase hydrocracking can be traced back to 1913, when Friedrich Bergius first demonstrated the process of liquefaction of coal by subjecting it to high pressure and temperature in the presence of hydrogen. The technology was commercialized and practiced in 12 commercial units dating back to the 1930s.

The subsequent development of this technology manifested into resid-conversion applications and fine tuned through integration with fixed-bed hydroprocessing to produce boutique products. This included commercial practice in multiple 10,000 bpsd trains during the 1950s and the 1960s and in a 3,500-bpsd unit from 1980 through early 2000 (Fig. 8).

 Fig. 8. History of slurry-phase hydrocracking.

While the process remained in practice for several decades, it found itself economically challenged during the era of low crude-oil prices and high natural-gas prices. The prevalent lower grade fuel specifications and available economic outlets for carbon rejection products such as fuel oil and petroleum coke also had a dampening effect on the widespread acceptance of this technology. A review of the historical data indicates that the interest in the technology peaked with inflated crude prices caused by man-made events such as war, international conflicts and oil embargoes, only to be deflated when these events proved to be short lived.

Can the technology handle residues irrespective of the feed quality? The slurry-phase hydrocracker follows the traditional principles of molecule management and catalytic chemistry and the technology configuration is engrained in the fundamental belief that residues and catalysts are inherently incompatible.

These principles are essentially the same as that of a delayed-coking process wherein the residues are handled in a thermal-cracking environment, preserving the residue-free, metals-free, CCR-free coker products for catalytic processing. In the case of delayed coking, the time temperature relationships allow for the hydrogen-deficient olefinic products of thermal cracking to either exit as lighter cracked materials or through condensation chemistry, progress to heavier carbon-rich molecules called coke.

The primary conversion chemistry in a slurry-phase hydrocracker essentially follows the same thermal induced initial cracking chemistry seen in delayed cokers. Due to the high hydrogen partial pressure and aided by sufficient hydrogen uptake, condensation reactions are severely inhibited, enabling the continued conversion to lighter products. There is little or no coke formation.

Fig. 9 shows data to demonstrate that near-complete once-through conversion of four different residues derived from a cracked-stock visbroken tars, bitumens (cold lake), traditional crude (Arab light) and de-asphalter bottoms can be achieved underscoring the feed flexibility afforded to a refiner through this approach. While many refiners tend to view high-sulfur heavy crudes as low-cost feedstock opportunities, the residues from these crudes are relatively easy to process. As shown in Fig. 10, the desired target conversion levels can be achieved at milder operating conditions.

 Fig. 9. Relationship between resid
 conversion and temperature for respective

 Fig. 10. Conversion vs. sulfur in respective

Viewed through the prism of molecule management and reaction chemistry, the refiner’s choices are likely to narrow down to an economic choice between the delayed coker, carbon rejection process and the noncatalytic slurry-phase hydrocracker, hydrogen-addition process. Both technologies are virtually immune to the quality of the residuum, with respect to the metals and CCR content, affording the refiner the luxury of a large basket of crude choices. In the case of slurry-phase hydrocracking, given that the process was derived from hydrogenation of coal, the choice of residue is unlimited, with sole exception of the extent of hydrogen consumption. This is essential a question of chemistry and hydrogen consumption is a mathematical balance reflecting the extent of hydrogen deficiency in the residuum and the desired high hydrogen content of Euro V products. The economics of carbon rejection and hydrogen addition in this case will be determined by the underlying assumptions regarding crude price and natural gas price projections.

Can the technology achieve near complete conversion on a once-through basis? While thermal-cracking processes and hydrogen-assisted thermal-cracking processes such as hydro-visbreakers have been practiced at various degrees of conversion, the key to accomplishing near-complete conversion of the residue lies in the ability to handle asphaltene precipitation and avoid fouling.

The process overcomes this limitation via using a proprietary noncatalytic additive that enables a near-complete conversion (> 95% wt) of the residuum on a once-through basis. The highly active surface area of the additive attracts the precipitating asphaltene molecules, the back-mix reactor hydrodynamics provides these molecules sufficient residence time to complete the conversion. The unconverted resid molecules that contain all the metals remain on the additive and are removed from the process.

The resultant 525°C minus products are resid free, asphaltene free, CCR free and metals free and are ideally suited for processing in a fixed-bed catalytic process. The process substantially distinguishes itself in its ability to accomplish a near-complete overall conversion and > 90 wt% asphaltene conversion (Fig. 11) irrespective of the CCR content of the feed. The selected operating conditions are critical to maintain stable operations at high once-through conversion.

 Fig. 11. Asphaltene conversion impacts on
 hydrogen consumption.

Can the technology produce finished diesel selective products? The process is essentially diesel selective. While the governing target for the slurry-phase reaction system is to achieve the 95 wt% conversion of the residue, the consequential high operating pressure, hydrogen partial pressure and treat rate at the fixed-bed reactor affords the refiner a virtually unlimited choice of catalysis and chemistry for the finishing step. With a relatively easy feed containing little or no deactivation precursors, the operating conditions are sufficient to do hydrotreating, hydrocracking, aromatic saturation, ring opening and dewaxing by simply modifying the catalyst systems.

A careful examination of the operating conditions and reactor system adopted in slurry-phase processes will easily explain the underlying basic principles that make the process distillate selective. In addition, with the issue of asphaltene precipitation and conversion squarely addressed by the additive, the process can now specifically avoid the more common strategies of limiting per pass conversion or the more expensive addition of aromatic solvents via recycle or from external sources. This would have a significant negative impact on the distillate product qualities.

As shown in Fig. 12, for a difficult residuum derived from one such opportunity crude “Athabasca bitumen,” 95 wt% once-through conversion, the process is diesel selective and will produce premium products. The naphtha can be directly fed to a catalytic reformer, the diesel will meet Euro V specifications, and the highly hydrotreated VGO can be an excellent feedstock to an FCC unit.

 Fig. 12. Yields and qualities—Athabasca

One alternate option would be to add external VGO or distillate streams directly to the fixed-bed reactor system and increase the overall VGO conversion through the catalytic process to achieve near complete conversion of the VGO. This would only further improve the total yield and quality of the diesel product derived from the unit.

Does the technology data base demonstrate the ability to handle a whole range of crudes? The key to formulating reliable, economic technology solutions is engrained in the ability to develop, regress, correlate and characterize these feedstocks. Since the characterization of residues is not easy, this understanding can only be derived from experimental data and correlating that behavior with other similar residues and processing objectives. While these principles are universal and well established, a refiner can only feel secure if the technology can be supported by several hundred data points, spanning a whole range of feedstocks (Fig. 13) and decades of research and development as proof of a complete understanding of the technology.

 Fig. 13. Representative crude basket to characterize
 resid conversion.

A review of the history of commercialization of new refining technology will show that units designed without this level of fundamental understanding, and without the appropriate due diligence can have a very difficult and arduous path to commercialization.

Can the technology do all of this with high reliability? The value of any technology can only be derived if reliable long-term operations can be sustained. In the case of resid upgrading, this reliability can only be achieved if high asphaltenes conversion can be accomplished without fouling or coking the unit.

The conversion chemistry here is essentially thermal in nature; potential condensation reactions associated with cracked molecules is arrested by the high hydrogen partial pressure. As the conversion progresses, and as the residuum loses its solvency, the additive provides the precipitating asphaltenes the required surface to adhere to, preventing equipment fouling or coking. The combination of high hydrogen partial pressure and noncatalytic additive system is unique and is a major contributor to the decades of reliable operation at high (> 95%), once-though conversion, with no signs of fouling. In the case of slurry-phase hydrocracking, reliability data, dating back to operations during the 1940s indicate that the process and chemistry has been proven to have consistently exceeded 90% onstream factor over several decades of operation.

Can the technology achieve all of this at an attractive NPV? A comparison of the NPV of three technology routes derived from upgrading a refinery residue as a function of benchmark crude price shows a remarkable trend in favor of slurry-phase hydrocracking. Both the economic and regulatory trends heavily favor slurry-phase hydrocracking, and the current and future market conditions are aligned with the inherent features of this technology.

The economic evaluation for one operating North American refinery VR as depicted in Fig. 14 clearly shows that the NPV of the ebullated-bed process only exceeds that of the delayed coker at a relatively high bench mark crude price of $85/bbl. This is primarily because of the lower conversion, stranded large volume of lower value unconverted residuum and the production of aromatic-distillate products that need retreatment.

 Fig. 14.  Economics of resid upgrading.

Conversely, the NPV of the slurry-phase hydrocracker exceeds that of the delayed coker at a benchmark crude price of $50/bbl, making this clearly the technology of the future.

Solutions for the future.

The authors believe that the prevelant market conditions going forward will favor hydrogen addition, and the technology that best addresses the seven questions is likely to dominate the resid-upgrading marketplace. The inherent features of the slurry-phase hydrocracking technology that ideally couple the feed molecules with the appropriate reaction chemistry is fundamentally sound and absolutely in sync with the best traditions of molecule management. It is no surprise that the results, when factored as conversion, product selectivity, product quality, reliability and overall economics will provide a compelling advantage over all other competing resid upgrading options. HP

The author 

Mitra Motaghi is a process engineer with the KBR Technology business unit with special focus on resid hydrocracking and VCC technology. She holds an MS degree in chemical engineering from Texas A&M Kingsville. 

Bianca Ulrich is a principal process engineer with KBR Technology business unit with special emphasis on resid hydrocracking and VCC technology. She holds a BS degree in chemical engineering from Georgia Institute of Technology. 

Anand Subramanian is Vice President for new technologies with KBR Technology business unit and is responsible for the VCC technology. He has 24 years of industry experience and 20 years with KBR in various process and technology management positions. 

Have your say
  • All comments are subject to editorial review.
    All fields are compulsory.


Slurry Hydroccracker seems interesting and I would like to know:
1- Who are the licensors?
2- What are the ranges of fresh catalyst or additives addition rate?
3- How can get rid of the desposed solids?
Thank you very much.


Very informative paper dealing all the aspects in a very analytical way. Its the Technology of today (or near future).

Related articles


Sign-up for the Free Daily HP Enewsletter!

Boxscore Database

A searchable database of project activity in the global hydrocarbon processing industry


Is 2016 the peak for US gasoline demand?




View previous results

Popular Searches

Please read our Term and Conditions and Privacy Policy before using the site. All material subject to strictly enforced copyright laws.
© 2016 Hydrocarbon Processing. © 2016 Gulf Publishing Company.